2012/5/19

Cleanest Process Explanation of Water Mill  

Wet sanding is a great alternative to dry sanding when repairs have been made to damaged drywall or plaster, as well as in remodeling that occurs in or near lived-in areas of the home. In wet sanding, the sponge is damp enough to significantly reduce the amount of sanding dust that becomes airborne. For this reason, persons with allergies living through a remodel or repair may well appreciate this alternative technique. In high-use areas of the home such as kitchens or baths, wet sanding can significantly decrease the mess that normally accompanies drywall repair.

Wet sanding is a cleaner alternative to regular sanding of drywall mud from remodeling and repairs. Wet sanding requires a special sanding sponge that replaces the traditional drywall sanding screens and blocks. The sanding sponge is used barely damp and requires frequent rinsing and wringing during wet sanding.

When properly executed, wet sanding does not alter the number of coats of drywall mud required, but the process does take longer than dry block sanding. This is mostly due to the number of times the sponge must be rinsed and wrung out, and depending on the size of the area, the water may need to be changed as well. You can reasonably expect to sand about a 3-foot square (about one square meter) section before needing to rinse and wring your sponge.

After wet sanding a coat of mud, allow the area to dry for about an hour before continuing with a second coat of compound or before painting or priming if the final coat has been sanded. Combining wet sanding with traditional sanding is also an alternative for home repair projects. Perhaps the first coat can be sanded with a traditional screen or block sander to expedite the process, but wet sanding can also be applied in the final coat so clean up can be performed sooner. Though it takes more time to complete a project with wet sanding, it is definitely the cleanest process.jaw breakers:http://www.hx-china.com/1.html
cement machinery:http://www.hx-crushers.com/p76.html

Keeping a bucket of water next to you to rinse your sponge is recommended, but you must change the water when it becomes too murky to see into. You can use different grain sanding sponges for wet sanding, such as coarse or fine, depending on which coat of mud you are sanding. Wet sanding sponges are slightly larger than a typical kitchen sponge and are available at most large home improvement stores.

When wet sanding an area, work in circles with a steady amount of pressure. The sanding sponge should be only slightly damp -- if water is dripping from the sponge when you apply steady pressure during sanding, the sponge is too wet.

The article is provided by Henan Hongxing,which is the professional manufacturer of complete sets of mining machinery, for example,jaw crusher supplier, it is always doing the best in products and service.
0

2012/5/19

Hypergrowth of Stamping Mill In Recent Years  

A stamp mill, sometimes called a stamping mill, is constructed with a series of stamps arranged in what is normally a wooden frame. There usually are five stamps in a frame, but this number can vary. Sometimes an individual frame with its set of stamps is called a stamp battery. Although some of the larger stamp mills were powered by steam engines, most use water for their energy source.

The term "stamp mill" usually refers to a type of mining equipment used to crush ore-containing rock, although it also can mean the building in which the rock is crushed. In ancient times, variations of the stamp mill were used for pounding grain, for processing oil from seeds and in the paper-making process. Traditionally, however, this type of mill machine has been used to mine gold, silver and copper.

Stamps usually are made of steel or something equally heavy, such as wood with iron heads. These stamps are operated by a cam and rotating shaft that are designed to cause the stamp to fall on the rock that is being fed through the machine. This process is repeated until the rock has been pulverized to the point where the target ore can be extracted.

Stamp mills or ball mills have largely been replaced by more modern means of ore extraction, but archaeological records indicate that variations of the stamp mill have been in existence for thousands of years. The early Greeks used components resembling those of the stamp mill for agricultural purposes, such as removing the hulls from grain. Gold and silver mining efforts during the period of the Roman empire show the use of stamps operated by a cam system. There are even sketches done by Leonardo da Vinci depicting a similar mechanism for use by blacksmiths.sand washing machine:http://www.crusher-machine.com/19.html
stone crusher plant:http://www.hx-crushers.com/p65.html

The process of pulverization by pounding with a heavy object is what differentiates stamp mills from grinding mills. Grinding uses some form of compression to break down a substance. The simplest example of grinding is what takes place in the use of a mortar and pestle.

One of the advantages to the stamp mill was the simplicity of its structure. It could be disassembled, transported to a new location and reassembled fairly easily. This meant that miners could use this type of mill machine in remote locations. The main restriction for a stamping mill was the availability of running water for power. In many cases, this was remedied by the damming or rerouting of nearby rivers or streams.

The article is provided by Henan Hongxing,which is the professional manufacturer of complete sets of mining machinery, for example,ore vibrating feeder, it is always doing the best in products and service.
0



teacup.ブログ “AutoPage”
AutoPage最新お知らせ